ISSN: 2690-0777
Open Journal of Environmental Biology
Research Article       Open Access      Peer-Reviewed

Western Sudan Arabi camel hides attributes and leather quality characteristics

Mohammed Alhadi Ebrahiem* and Idris Adam Idris

Department of Animal Production, Faculty of Natural Resources and Environmental Studies, University of Kordofan, Sudan
*Corresponding author: Mohammed Alhadi Ebrahiem, Department of Animal Production, Faculty of Natural Resources and Environmental Studies, University of Kordofan, Sudan, E-mail: [email protected]
Received: 20 October, 2021 | Accepted: 24 November, 2021 | Published: 02 December, 2021
Keywords: Western Sudan; Arabi camel; Camel hides attributes; Leather quality

Cite this as

Ebrahiem MA, Idris IA (2021) Western Sudan Arabi camel hides attributes and leather quality characteristics. Open J Environ Biol 6(1): 040-043. DOI: 10.17352/ojeb.000025

Copyright

© 2021 Ebrahiem MA, et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

This study was aimed to evaluate camel hide attributes and leather quality characteristics of Western Sudan Arabi camel. Thirty pieces of fresh camel hides from three subtypes of Western Sudan Arabi camel ecotype (10 pieces from each of Kababish, Meidob, and Hawawir subtypes) were collected, cured, and tanned. Physical and chemical quality parameters were assessed. The data were analyzed using the Complete Randomized Block design. The results revealed that Significant differences (P≤0.05) were detected among Western Sudan Arabi camel subtypes fresh hides thickness and weight. Kababish hide thickness and weight were recorded the highest value of 0.155±0.4 cm and 11.7±1.3 Kg respectively in comparison to Meidob (0.145±0.3 cm and 8.6±1.2 Kg) and Hawawir (0.143±0.4 cm and 7.7±2.2 Kg). Kababish hides thickness value was above the minimum Sudanese standard threshold specification for cattle leather quality. While Meidob and Hawawir hide thickness values were blew the minimum Sudanese standard threshold specification for cattle leather quality. Physical quality parameters; elongation, tensile strength, resistance to grain cracking, breaking load, and tear strength; were in the Sudanese standard threshold specification for cattle leather physical quality of 100%, 200 Kg/cm2, 7N/cm, 8 N/cm, and 100 Kg/cm2respectively. Whilst flexibility parameter was below the Sudanese standard threshold specification for cattle leather quality. Chemical quality parameters were in the Sudanese standards threshold specification for cattle leather chemical quality of 18%, 4.5%, 2.5%, and 11% for moisture, Ash, chrome oxide, and fat contents respectively.

Introduction

Camels constitute 22% of the animal census in Sudan and 26.3% of the camel population in the Arab world. The estimation of the camel’s population in Sudan was about 3,908 thousand heads [1]. These camels are spread in a belt that extends between latitudes 12-16N [2]. Since their domestication, camels have played a vital role in the daily life of many societies, where other livestock farming operations cannot be easily practiced [3]. Camels provide humans with a range of products and services, from fine wool to meat, milk, and draught power. Camels have the ability to go for long periods without water and live on thorny and high fiber diets, stand high altitudes, and extreme temperatures, making them one of the few families well adapted for food and agricultural production under harsh semi-desert environments [2,4].

Camels in Sudan and elsewhere are classified as a pack (heavy) and riding (light) types according to their function. Recent studies had been made to classify the camels according to their performance like dairy camels, meat camels, dual-purpose camels, and racing camels [1,5]. The Arabi Type is a heavy type that makes up the majority of the camel maintained by nomads about 80% [6]. They are sub-grouped into Arabi types and Rashaidi (Sawahli) types.

The Arabi type found in Kordufan, Darfur, and the Blue Nile constitute about 96%, and in eastern Sudan, it is about 55% of the total in that area. Most of the Sudanese camels are large heavy massive types with slow mobility [6]. Mainly the Arabi type is described as a large heavily built animal with a well-developed hump, and it has short hair except in the shoulder and hump. The mature camel weighs about 400- 500 kg as a life weight, and can carry about 275 Kg over 25-30km per day, and is sandy gray. In western Sudan, the Meidob and Hawawir have herds of comparatively lightweight camels; some of which can be ridden [7].

Materials and methods

The study area

Kordofan region is located between latitudes 9°:30ˉ-16°:30ˉ North and longitudes 24°- 32°:25ˉ East. The region consists of North, West, and South states forming a total area of 380,000 Km2 (90 million feddan). Each of the three states existed independently of one another while subscribing to the authority and jurisdiction of the federal government [8].

Selection of experiment camel hides

Thirty (30) pieces of fresh camel hide from three (3) Arabi camels'subtypes (10 pieces from each of Kababish, Meidob, and Hawawir subtypes)which bring from different geographical areas from West Sudan (Kordofan Rejoin).

Tanning procedures

Leather was prepared from camel hides according to the following main steps: Soaking, Liming, Deliming, Bating, Pickling, Tanning, Neutralization, and Re-tanning (Table 1). Sampling and assessment of chemical and physical characteristics were done according to SSMO (Sudanese Standard and Meteorology Organization) methodology. Physical properties that were assessed are: Tensile strength and elongation% according to [9], Flexibility test according to [10] and Measurement of tearing load and resistance to grain cracking according to [11]. Whilst, chemical characteristics were: moisture% according to [12], total Ash% According to SSMO2 (2006), fats and oils% according to [13], and chromium% according to [14] procedures.

Statistical analysis

The data were statistically analyzed according to Complete Randomized Block Design using SPSSv.14.0 software package [15]. LSD test was used for means separation, besides comparing skin and leather measurements results with Sudanese Standard thresholds for leather quality according to SSMO standards.

Results and discussion

Western Sudan Arabi camel fresh hides attributes

Significant differences (P≤0.05) were detected among Western Sudan Arabi camel subtypes fresh hides thickness. Kababish subtype of Western Sudan Arabi camel was scored the highest value of0.155±0.4 cm in comparison to 0.145±0.3 cm and 0.143±0.4 cm for Meidob and Hawawir subtypes respectively (Table 2). Kababish subtype hide thickness value was above the minimum Sudanese standard threshold specification for cattle leather quality. While Meidob and Hawawir Arabi camel subtypes their hide thickness values were blown the minimum Sudanese standard threshold for cattle leather quality. Generally the thicker the hide is plump and stout. The properties of leather and its uses depend on the characteristic of the fiber bundles such as fullness, disorderliness, compactness, straightness, delineation, boldness, splitting, and separation. Poor nutrition causes an animal to be smaller and the skin or hide to be thinner and to be a poorer substance [8].

Also, Significant differences (P≤0.05) were detected among Western Sudan Arabi camel subtype's fresh hide's weights. Kababish subtype of Western Sudan Arabi camel has scored the highest value of 11.7±1.3 Kg in comparison to 0.145±0.3 Kg and 7.7±2.2 Kg for Meidob and Hawawir subtypes respectively (Table 2). [16,17] stated that the most prominent features of fresh hides and skins (from cattle, and sheep/goats respectively) are their size, pelage, and color. All these are more or less closely related to the breed of the animal. The size (weight) of a hide or skin is closely related to the weight of the animal from which it came, and is typically between 7 and 11% of the live weight. Accordingly, the hide of a 1,000 kg bull may be as much as 110 kg while the skin of small (25 Kg) sheep or goat may be as little as 1.8 kg (less in the case of a lamb or kidskin). This variation in size has innumerable implications during the course of tanning and will be referred to later.

Western Sudan Arabi camel leather physical quality parameters

Significant differences (P≤0.05) were detected within the parameters’ values of elongation, tensile strength, breaking load, and flexibility respectively. The highest elongation% and tensile strength Kg/cm2, breaking load N/cm and flexibility% values of 44.73±2.2%, 225±6.5 Kg/cm2, 9.84±0.55 N/cm and87.20±3.9% respectively, were reported for Kababish subtype leather. On the other hand, no significant differences (P≥0.05) were detected among the values of resistance to grain cracking and tear strength parameters respectively. The highest resistance to grain value and tear strength of 6.74±1.8 N/cm and 95.56±5.3 Kg/cm2 were reported for Hawawir subtype leather. Elongation, tensile strength, resistance to grain cracking, breaking load, and tear strength parameters were in the Sudanese standard threshold specification for cattle leather quality. These results confirm with [18] who mentioned that camel leather physical quality elongation percentage, tensile strength, resistance to grain cracking and breaking load of 33.85±10.42%, 207.97±11.32 Kg/cm2, 6.35±0.69 Kg/cm2, 7.57±0.68 Kg/cm2 respectively were in the Sudanese, Indian and Europe standards for leather quality of 45%, 200 Kg/cm2, 7.0 Kg/cm2 and 8.0 Kg/cm2 for the mentioned characteristics respectively. Whilst flexibility parameter was below the Sudanese standard threshold specification for cattle leather quality [18] found that, flexibility parameter for Arabi camel was 59.3±3.77% and blew the Sudanese, Indian, and European standards for leather quality of 100% for the mentioned characteristic (Table 3).

Western Sudan Arabi camel leather chemical quality parameters

Significant differences (P≤0.05) were detected among moisture and chrome oxide content values respectively. But no significant differences (P≤0.05) were observed among Ash and fat contents values respectively. Chemical quality parameters were in the Sudanese standards threshold specification for cattle leather quality of 18%, 4.5%, 2.5%, and 11% for moisture, Ash, chrome oxide, and fat contents respectively. These results confirm [18-22] who mentioned that camel leather chemical quality parameters; moisture, Ash, chrome oxide, and fat of 4.61±0.26%, 6.21±0.30%, 3.28±0.29%, and 9.46±0.38% respectively were in the Sudanese, Indian and Europe standards for leather quality of 18%, 4.5%, 2.5% and 11% for the mentioned characteristics respectively (Table 4).

Conclusion

Camel leather is similar in it is quality to cattle leather. Therefore camel leather is suitable for manufacturing all types of leather articles those cattle leathers are used for. But with less quality in flexibility which will reflect in the less expected lifetime of camel leather articles in comparison to cattle leather articles.

  1. Ishag I (2009) Production system, Phenotypic and Molecular Characterization of Sudanese Camels (Camelus dromedarius). PhDThesis. Department of Genetics and animal Breeding, Faculty of Animal production, University of Khartoum- Khartoum, Sudan. Link: https://bit.ly/3o6AF9R
  2. Wardeh MF (2004) Classification of the Dromedary Camels. J Camel Sci 1: 1-7. Link: https://bit.ly/3FZpHZT
  3. Kadim IT, Mahgoub O, Mbaga M (2014) Potential of camel meat as a non-traditional high quality source of protein for human consumption. Animal Frontiers 4: 13-17. Link: https://bit.ly/3litkT2
  4. Gihad EA (1995) Arabian camels, production and culture. Department of Animal production, Faculty of agriculture, Cairo University, Arab publishing and distributing company.
  5. Kalafalla AI (1999) Camel Breeds in the Sudan. Albuhuth J. Sci National Center for Research 8. Part (1). Forth Scientific Conference.
  6. Abbas BN, Chadeuf G, Saint-Martin P, Bonnet A, Millaird H, et al. (1992) Camel pastoralism in the butana and North Eastern Sudan: an interdisciplinary study Nomadic person 31: 66-84. Link: https://bit.ly/3IhT8bR
  7. Hashim WM, Galal MY, Ali AM, Kalafalla AI, Hamid SA, et al. (2015) Dromedary camels in sudan, types and sub types, distribution and movement. International Journal of Pharmaceutical Research & Analysis 5: 8-12. Link: https://bit.ly/3o4ZwuG
  8. Ebrahiem MA (2015a) Leather Quality of Sudan Desert Sheep goats. Lambert Academic Publishing, Germany Link: https://bit.ly/3pgy4tc
  9. SSMO5-Sudanese Standard and Metrology Organization (2003) Leather standards: leather physical tests- Tensile Strength. Khartoum, Sudan .
  10. SSMO6-Sudanese Standard and Metrology Organization (2001) Leather standards: physical tests for upper leather- Khartoum, Sudan .
  11. SLTC -Society of Leather Trades Chemists (2015) Official methods of analysis. Fourth revised edition- Society of leather trades chemists 52 crouch hall line, Redbourn, Herts.
  12. SSMO1 -Sudanese Standard and Metrology Organization (2006) Leather standards: determination of moisture in leather- Khartoum, Sudan .
  13. SSMO2 -Sudanese Standard and Metrology Organization (2006) Leather standards: determination of Ash in leather- Khartoum, Sudan .
  14. SSMO3 -Sudanese Standard and Metrology Organization (2006) Leather standards: determination of chrome oxide in leather- Khartoum, Sudan .
  15. SPSS (1996) Statistical Packages for the SocialSciences. Cary, North Carolina.
  16. Ebrahiem MA, Ali MA, Turki I, Haroun HE, Bushara I, et al. (2015b) Defects and Grading of Hides and Skins in Kordofan Region, Sudan. Lambert Academic Publishing, Germany. Link: https://bit.ly/3d1bn6D
  17. Teklebrhan T, Urge M, MekashaY (2012) Skin/leather quality of indigenous and crossbred (Dorper x Indigenous) F1 sheep. Haramaya University, School of Animal and Range Sciences, P.O Box 138, Dire Dawa, Ethiopia. Link: https://bit.ly/3o5zuHG
  18. Ahamed HA, Hamed A, Alhadi M, Ebrahiem MA (2021) Evaluation of Sudanese Arabi Camel Hides for Leathers Manufacturing. EC veterinary Scinece 10: 13-31. Link: https://bit.ly/32Q4Ji5
  19. SSMO7 -Sudanese Standard and Metrology Organization (2004) Leather Standards: for garment leather- Khartoum, Sudan .
  20. SSMO8-Sudanese Standard and Metrology Organization (2008) Leather metrology: for lining leather - Khartoum, Sudan .
  21. SSMO9 -Sudanese Standard and Metrology Organization (2008) Leather Standards: for shoe upper vegetable and chrome tanned leather-Khartoum, Sudan.
  22. SSMO4 -Sudanese Standard and Metrology Organization (2006) Leather standards: determination of fats and oils in leather- Khartoum, Sudan .
 

Help ?